Crius All In One Pro Flight Controller V1.0

[Gaza07]

Rctimer have a very nice flight controller at a good price that is suitable for megapirate and multi wii
The All in On Pro V1.0, this looks like a very good choice foranyone looking for a new flight controller as it has all the new sensors and the full atmega2560 mcu below are the pics and specs from the rctimer web page

Features:
         ·Supported MegaPirateNG and MultiWii firmware
         ·Up to 8-axis motor output
         ·8 input channels for standard receiver
         ·4 serial ports for debug/Bluetooth Module/OSD/GPS/telemetry
         ·2 servos output for PITCH and ROLL gimbal system
·A servos output to trigger a camera button
         ·6 Analog output for extend device
         ·A I2C port for extend sensor or device
         ·Separate 3.3V and 5V LDO voltage regulator
         ·ATMega 2560 Microcontroller
         ·MPU6050 6 axis gyro/accel with Motion Processing Unit
         ·HMC5883L 3-axis digital magnetometer
·MS5611-01BA01 highprecision altimeter
·FT232RQ USB-UART chip and Micro USB receptacle
         ·On board logic level converter
         ·Match the standard of RoHS

◆Flight mode for Multiwii
         ·One of the following basic mode
                  - Acro
                  - Level
                  - Alt Hold
                  - Head Lock
         ·Optional mode
                  - HeadFree (CareFree)
                  - GPS Hold (Need GPS receiver or Extend Board)
                  - GPS Back to home position (Need GPS receiver or Extend Board)

◆Flight mode for MegaPirate
         ·Acro
         ·Alt Hold
         ·Simple
         ·Loiter (uses GPS)
         ·Guided (uses GPS)
         ·Position (uses GPS)
         ·Circle (uses GPS)
         ·RTL (uses GPS)
         ·Auto(uses GPS)
         ·Follow Me(uses GPS)

◆Input power selection
         ·One of the following way
                  - Connect 5V power cable from ESC or UBEC to the ESC/Servo port, the J1 jumper must be closed.
                  - Connect 5V~12V power cable to the extend power port, the J1 jumper must be removed.
           When using Extend Board, AIO PRO must be powered from the extend power port.

◆Other
         ·Dimension: 50mmX50mm
         ·Height: 11.6mm
         ·Weight: 14.2g
         ·Fixing hole spacing: 45mm
         ·Hole diameter: 3mm

◆Package content
         ·AIO PRO FC x 1
         ·3Pin to 1Pinx3 cable 100mm x 3
         ·3Pin to 3Pin cable 100mm x 1
         ·Molex 1.25mm 4Pin cable 100mm x1
         ·Molex 1.25mm 6Pin cable 100mm x2
         ·Molex 1.25mm 8Pin cable 100mm x1

http://www.rctimer.com/index.php?gOo=goods_details.dwt&goodsid=765&productname=

http://www.rctimer.com/index.php?gOo=goods_details.dwt&goodsid=766&productname=

[MadMax]

Thats a very nice looking flight controller and with a very good price tag too, its been a while since I visited rctimer they seem to have really stocked up on multi rotor gear 
theres an expansion board available for this F/C too  8)

[Gaza07]

You mean the board in the picture below its got Gps and an Xbee telemetry port, I didnt post it before because it cost more than the flight controller does, and your then stuck with buying Xbees which arent cheap there are much cheaper alternatives around to the Xbee and some very good Gps modules for much less like the one they sell which is also Ublox,
Although it would all look very neat and tidy when all put together  8)

[MadMax]

Isnt the expansion board worth having ? 

[Gaza07]

It is if your going to get Xbees's for telemetry but there are other options that I would use like the APC modules and seperate GPS, or the new 3dr telemetry set once the bugs are ironed out  ;D