Welcome to Multi-Rotor UK. Please login or sign up.

Tuesday,March 18, 2025, 23:47:18

Login with username, password and session length

Shoutbox

Bad Raven:
12 May 2024 08:13:51
 I have some F1 Abusemark boards going spare,,,,,,,,,,,,,    ;)    :azn
DarkButterfly:
11 May 2024 22:12:29
And with oldskool parts  :D
DarkButterfly:
11 May 2024 22:11:57
I must be the only one doing tricopters right now  :laugh:
DarkButterfly:
11 May 2024 22:09:30
 :D
Gaza07:
11 May 2024 21:15:16
Domain has been renewed closure has been cancelled  :D
Gaza07:
02 May 2024 08:07:52
Who are most people ??? I think the person you are referring to has put in a lot of effort to keep things moving  :rolleyes:
hoverfly:
01 May 2024 10:16:12
Most people I have spoken to are pizzed off with the yellow peril  flooding the forum,go figure. :whistling:
Gaza07:
23 Apr 2024 08:09:45
The Domain expires for the forum in 60 days, I'm not going to renew it this time unless I see any activity  :beer2:
Gaza07:
20 Apr 2024 18:02:50
Is there anyone who would like to see this forum stay open ? :shrug:
hoverfly:
17 Apr 2024 17:15:13
 :rolleyes:
Members
Stats
  • Total Posts: 201,519
  • Total Topics: 20,276
  • Online today: 36
  • Online ever: 530
  • (Tuesday,June 26, 2012, 08:34:46 )
Users Online
Users: 0
Guests: 20
Total: 20

Theme Changer





3d - Printworx

Ev100 diversity mod_how I did it

Started by tipsy trucker, Saturday,January 26, 2019, 20:37:04

Previous topic - Next topic

tipsy trucker

I know it's been done before but I did it a slightly different way, which I found easy so I thought I'd share. Obviously this is on your own head, will certainly void warranties and could result in anything from magic smoke to death..... etc etc

Firstly, I got the eachine pro58 Vrx and flashed it with perx firmware

The plan was to try to remove the existing receiver which is simply soldered to the main board. However, I found "pinouts" for both receivers and they're not the same unfortunately (besides, the pro58 wouldn't have fitted physically).

A video of the process on YouTube explained that I'd need to use a 5v regulator which I didn't have to hand so I went a different route....

A few minutes with a Stanley knife cutting the solder on the original receiver got that out in short order - certainly quicker than wicking it away.

Then, using the pinouts off t'internet I soldered 8 wires to where the old receiver once was (9 minus rssi); two slightly thicker for the +5v and ground and 6 cut from an old hard drive ribbon cable.

That done, I removed the pins from the pro58 so I had a row of 9 holes and soldered my wires through their relevant "hole"

All up and running and some bad news for me but good news for you....

The buttons won't work as far as I can see but the knob kinda button on the new receiver works fine so save yourself the hassle and just do the 5v+, gnd and video and all will be well!

If you're handy with a soldering iron and Stanley knife I reckon this can be done in half an hour, I just wish I'd taken pictures as I went along. Hope this helps

ched

Interesting. Have you tested yet?
Picys would have been very handy. Well done.

How have you mounted the pro58? Do you have any picys of that?
I try :-)

tipsy trucker

#2
The receiver came with a double sided sticky pad so I've just stuck it to the top of the goggles above my left eye; not as tidy as I was hoping for but it's ok. I trimmed a small notch out of the case to get the wires through.

I have tested and signal seems to be very strong, unfortunately I didn't have the patience to try it as standard first (the weather hasn't been kind so I took the opportunity to do the mod instead) so I can't compare really.

To make up for the photos a little; once you've removed the receiver you'll have a row of 9 pads on the board and two sets of three above them where the antennae were connected. Along the 9; 4th is gnd, 5th is 5v and 8th is video (9th is also ground which you may need for the video) that's left to right if the antenna are at the top.

On the pro58, with the screen facing you and the antennae at the top (the connections are underneath); 1st is 5v, 3rd is gnd  (2nd is also gnd) and 6th is video (again from left to right)


tipsy trucker

What I found with the buttons is that you need to enable "fs buttons" on the pirx menu but the frequency will change 1hz and go straight back to where it was, it also changes frequency at random and loses signal so I've disabled fs buttons and I'm happy enough with how it works now. Whether I did something wrong or if fatshark buttons work differently to whatever's coming out of the board - I've no idea but it's not a problem to me.

For the notch that the wires go through, I cut away the lip on the top half of the casing with a Stanley knife where the two halves join and then shaved about .5mm deeper than that. In my case about 10mm wide but for three or four wires I'm sure you could half that