Kakute f4 AIO

[hoverfly]

Finally got to test fly the Kakute f4 aio today,  it had been hovered indoors for a few mins just to check it out but  that was it.
I';m not really into mini quads as i';m crap at flying them but this is a game changer , it';s solid.After a couple of batts i was flying it like i stole it and on stock settings. The goalpost avoidance system works perfectly, and i managed a few back flips, the first one was not intentional  but after i worked  out how it happened i tried a couple more. Only one arrival due to very gusty wind  trying to avoid a tree.

[ched]

Well done mate. Where are the quad picys or even a video? 

[hoverfly]

Well done mate. Where are the quad picys or even a video? 

Too embarrassed to post pic, its on a Diatone Colour  frame with junk box Emax MT2204- 2300kv  motors Dys Bl heli  optic ESC, Spek sat. I';m  so impressed i will probably build a fpv 250 and keep this one for experimenting on.
I haven';t got this excited over a f/c for ages this one has really got my frock up..
Attached is the pic i';m not going to post..

[ched]

Looks good to me. If it flies and goes where you ask it is good 

After having issues with Omnibus FC I am thinking I should look at an alternative.

The Kakute f4 aio is one I have considered but not sure on height (tight stack in Martian3). Can you tell me the height below the pcb, the thickness of pcb and height above pcb?

The other I am considering is the Matek F405 AIO but it means having batt connections at the side which may be vulnerable when I crash. Neither have baro and I was thinking it would be nice to see an idea of altitude.
Suppose I can';t have it all 

[DarkButterfly]

That';s awesome, the Kakute F4 is rock solid even on stock settings, it supports SmartPort telemetry and lua scrips on the Taranis so tuning is a breeze.
They';ve hit the mark on this one

[hoverfly]

Ched, dims on the manual 
Oops file too big,the board is 7mm total thickness.

https://www.google.co.uk/url?sa=t&source=web&rct=j&url=http://www.unmannedtech.co.uk/uploads/6/7/0/2/6702064/holybro_kakute_f4_aio_manual_v1.4.pdf&ved=0ahUKEwiZn52Fv-bVAhXOhrQKHSJzBzoQFghnMAY&usg=AFQjCNHB1HAmDX-Vf3Ceh6Z1zwUZveJ0Ug

Only problem I had was the pads have varnish on them,I gave them a scrub with a cotton bud with acetone  then a dab of flux pen,they then soldered a treat.

[ched]

Ched, dims on the manual 
Oops file too big,the board is 7mm total thickness.

Only problem I had was the pads have varnish on them,I gave them a scrub with a cotton bud with acetone  then a dab of flux pen,they then soldered a treat.

Thanks.
I did have a look through the manual but it only lists total height at 7mm. I currently only have about 1mm of clearance in the stack before hitting the top plate. So limited on standoff sizes. I think it would be fine as I currently have 7mm anti vib standoffs which I wouldn';t need so could probably go to 4mm which gives me an extra 3mm that could go on top of the Kakute.
Cheers and have fun.

[Dippi]

Any recommendation from where to order the frame?

[Dippi]

https://hobbyking.com/en_us/kakute-flight-controller-f4-aio-v1-4.html

Is this the right one?

[shawdreamer]

was hoping someone would give one of these a good run, might slot one into my newest design instead of a stock';ish f4

[hoverfly]

Any recommendation from where to order the frame?

The frame came from my junk box ,it has been discontinued..

[hoverfly]

was hoping someone would give one of these a good run, might slot one into my newest design instead of a stock';ish f4

Go for it, i recharged the batts and had to nip out and have another quick buzz when the wind dropped. If you use Spektrum  sat it can';t be bound via the C.L.I.  you have to bind with a main receiver before soldering, not mentioned in manual.

[Dippi]

ordered mine, may ask for help to set it up.

[Dippi]

The only thing i fail to understand, why all these FC don';t come with preinstalled pins to push in wires, instead of solder pads.

[DarkButterfly]

The only thing i fail to understand, why all these FC don';t come with preinstalled pins to push in wires, instead of solder pads.

Its about saying space and weight, plus solder pads are better as it means a cleaner install.

[Dippi]

Its about saying space and weight, plus solder pads are better as it means a cleaner install.

Its a misery to solder if you have had no previous experience 

[ched]

Its a misery to solder if you have had no previous experience 

There is a very good manual here: http://www.unmannedtech.co.uk/manuals/kakute-f3-all-in-one-manual. Have a good read, it should help you understand. The manual is written by Joshua Bardwell, so a very experienced guy.

[Dippi]

There is a very good manual here: http://www.unmannedtech.co.uk/manuals/kakute-f3-all-in-one-manual. Have a good read, it should help you understand. The manual is written by Joshua Bardwell, so a very experienced guy.

Will do, Lucky i ordered last night, now the price has gone up for the FC.